Tuesday, June 7, 2022

Drilling Innovations That Will Forever Change the Oil Industry



Oil drilling has now been practiced for over a century. The sector has developed by leaps and bounds as a result of several technological breakthroughs. This expansion has resulted in new advances in oil production that are altering the face of our civilization.

As early as 1880, the globe witnessed one of the earliest developments known as the rotary drill, which dramatically enhanced the oil drilling process. This rotary drill, however, was just the beginning of a lengthy line of subsequent developments that would eventually replace it in the twentieth century. In this post, we'll look at some of the most significant breakthroughs in oil production efficiency.

1. Offshore Drilling and ROVs

Oil drillers quickly discovered that wells located near seashores generated the most oil. This is why the industry needed to develop technologies for extracting oil from the seafloor. Drilling companies built oil rigs on several wharves in the 1980s, but the first oil well on land was discovered somewhere about 1947.

Remotely operated vehicles were among the early technologies that aided the establishment of these offshore drilling enterprises (ROVs). The US military was already using this technique to recover equipment that had been lost at sea. The oil sector was exploiting ROVs for their own purposes by the 1970s.

2. Hydraulic Fracturing

Fracking, or hydraulic fracturing, is another new technology that Shale Gas relies on. This approach, which was created in 1940, has grown in popularity. Fracking is based on tight reservoirs, which often contain oil-bearing rocks with small holes, implying that the flow of oil from these is limited.

Drillers utilize fracturing to stimulate these wells by putting chemicals mixed with water into the well to produce pressure. This pressure, in turn, causes fractures in the rocks that can be hundreds of feet long. After these fissures are created, oil is allowed to flow freely out of the rock. According to numerous studies, fracking has contributed to an additional seven billion dollars oil barrels from wells in the United States.

3. Seismic Imaging

Initially, looking for oil wells was based solely on where oil had bubbled to the surface. Because most oil wells are buried far beneath the earth's surface, they cannot be discovered. Digging deep wells to set up rigs only to find barren patches was also highly costly.

Geologists were brought in to devise methods for locating oil wells that were hidden. They devised numerous approaches, the most important of which was 3-D seismic imaging. This system transmits sound waves into the ground and detects signals as the waves bounce off of obstacles.

This technology not only assisted in locating the most productive locations for establishing oil production units, but it also reduced the number of holes that were drilled without success.

4.   Measurement-While-Drilling Systems

One major disadvantage of seismic technologies was that they did not provide drilling operators with precise information about the amount of oil they were working with. These concerns were resolved in the 1980s thanks to a technology known as measurement-while-drilling (MWD).

With this system and its reliance on'mud pulse telemetry,' operators were able to collect and analyse real-time data, allowing them to establish the state of the oil well. This technology, in turn, enabled operators to drive oil wells in different ways based on the data they had gathered.

5.   Horizontal Drilling

We emphasized the potential of operators to steer their oil drilling operation in multiple directions while discussing MWD technologies. This capacity to drill in directions other than straight has become one of the most significant technological achievements in the history of the oil drilling process.

Oil reservoirs tend to be spread out horizontally from time to time, making vertical wells an ineffective method of extraction. This is why these technologies enable operators to dig vertically initially and then pivot to a horizontal well at the 'kick-off point.'

This technology has not only enabled the extraction of oil from horizontal wells, but it has also assisted operators in conducting their operations in a more environmentally friendly manner. The first horizontal wells were dug in 1929, but the process was prohibitively expensive at the time. However, with the introduction of hydraulic fracturing, horizontal drilling became a more inexpensive and realistic choice. By the late 1980s, nearly all oil drilling companies across the world were adopting horizontal drilling.

Read More → Drilling Innovations That Will Forever Change the Oil Industry

Key of Technologies are Advancing Oil and Gas Drilling

Oil and gas (O&G) is still a thriving industry, managing $1.7 trillion USD per year and requiring over 94 million barrels of petroleum per day globally. It is expected that demand for fossil fuels would rise by around 25% during the next 22 years. As a result, in an era when automation, digital process control, and IoT are regarded as "common innovation processes," oil and gas companies have begun to adopt technologies that can assist them in gaining access to small isolated offshore reservoirs as well as areas characterized by extreme environments.

The 2016 Upstream Oil and Gas Digital Trends Survey identified eight critical areas in which the O&G industry should adjust in order to reap the benefits across their extractive environments. The fastest developing fields among them were robotics and drones, artificial intelligence, and wearable technology.

At the moment, more than 80% of Oil and Gas enterprises are undergoing a digital transformation that has the potential to unleash $1.6 trillion USD by enhancing reliability, optimizing operations, and creating new value. Furthermore, the adoption of "common innovation processes" can assist the O&G industry in gaining environmental credibility because robotics and drones, artificial intelligence, and wearable technologies offer tangible options for reducing greenhouse gas emissions, saving water, and avoiding oil spills, for example. Finally, modern operational technology translates into more efficient and less risky operations, and has the potential to deliver a wealth of process data to optimize O&G extraction procedures.

A number of developing technologies can help the O&G business comply with health, safety, and environmental regulations while also being cost-effective.

Robotic drilling systems (RDSs) provide entirely unmanned drill floors for both land and offshore operations. RDSs can handle pipes and tools, as well as replace casing crews and tongs, and they can handle machinery that revolve. Furthermore, cutting-edge drilling technology provides self-moving autonomous drill rigs that may be transported around an oil field from one well position to the next.

In-pipe inspection robots (IPIRs) can identify fractures, corrosion, and severe problems in pipes, which can cause pipe failures and halt output. These robots have nondestructive testing sensors that are embedded in the pipeline network. IPIRs operate autonomously at this point. They can send data and control signals; for example, IPIRs feature wireless sensor networks (WSNs) that can detect sand buildup, pipe damage, vandalism or theft, and fluid leaks in addition to monitoring pipeline integrity. WSNs are intended to communicate across the relay node, transmitting data to a single base station.

Unmanned aerial vehicles (UAVs) are another option for inspecting O&G facilities. Drones are increasingly being used to monitor tanks, pipelines, and refineries on a regular basis. Drones are frequently operated from a ground control station, necessitating the use of advanced flight control algorithms, inertial navigation, data fusion, and tracking control. These characteristics make drones useful for exploring O&G reservoirs in severe situations where human investigation is not feasible. To undertake faster and safer inspections, drones can be outfitted with a thermal camera, lights, and optical camera operators.

Aside from smart sensors and machine interface, recent advancements in 4D seismic data gathering and computer capacity are assisting O&G businesses in capturing more accurate subsurface geology for finding fossil fuel resources.


Oil and gas corporations who are already looking ahead:


Maersk Oil has established a new unmanned platform, the Tyra Southeast-B, in the Danish North Sea, following the operation of the first unmanned, fully automatic, and remote operating platform, the Norwegian Oseberg H, located on the Norwegian Continental Shelf. Tyra's reserves are predicted to grow by 50 million barrels of oil equivalent (MMBOE) during the next three decades.




Statoil, Enegi Oil (Nu-oil), the Wood Group, and the China Offshore Oil Engineering Company are concentrating their efforts on operations to access more minor reservoirs. Small reservoirs have recoverable reserves of less than 20 MMBOE. According to Enegi Oil, there are 88 fields in the North Sea with fewer than 15 MMBOE that can be developed using buoy technology, for example. Others are taking notice of the region north of the Arctic Circle, which "may contain roughly 30% of the world's undiscovered gas and 13% of the world's unknown oil deposits."

In Canada, Statoil and Husky Energy are exploring drilling for oil and gas resources in deep-water, far-offshore oil 500 kilometers off Canada's east coast, in the Flemish Pass Basin, using ocean and subsea technology, remote sensing, and autonomous underwater vehicles.

To summarize, automation and digitalization may provide certain benefits to the oil and gas industry in terms of safety, environmental performance, public health, productivity, operations, efficiency, reliability, and investment. To remain competitive, oil and gas companies must evolve, as the means in which energy is generated, consumed, and distributed have changed tremendously. We are living in an era in which people have more decision-making power based on real-time data.


Read More → Key of Technologies are Advancing Oil and Gas Drilling

Friday, March 22, 2019

The challenge to Drill the depth of the New Offshore Wells

drill the depth

About 80 kilometers from the coast, 1,500 meters below the water surface. The "numbers" of Macondo make an impression: just ten years ago the idea of ​​extracting oil on the high seas, at such high depths, was simply science fiction. And yet, faced with the greatest ecological disaster in the history of the oil industry, there is a comment that recurs with particular frequency among the experts: "BP was not dealing with a difficult well".

Over the course of a few years, the progress of offshore technologies has been so great that it has allowed companies to achieve the limits of the impossible, in front of which Macondo seems almost an amateur exercise. The Deepwater Horizon itself, the platform exploded on April 20, had just broken the submarine drilling record, identifying - again on behalf of BP and always in the Gulf of Mexico - the Tiber field, 10.6 km above sea level, of which over 9 under the backdrop.

There were 33 other offshore installations engaged in exploring the seabed at depths equal to or greater than those of Macondo in the United States. After the Macondo incident, the White House ordered that everyone stay for six months, waiting. of a crackdown on security conditions. The overall number of drills in the Gulf of Mexico, however, is much higher: according to the statistics of Rigzone, in April there were 243, of which about half were in use (in the world they were 578). As for the number of wells, the bottoms in front of Texas and Louisiana are literally studded with holes: it is estimated that there are about 3,500, dug with increasing frenzy as the search for crude oil on the mainland became more difficult, due to the decline of the most "at hand" fields and the spread of so-called resource nationalism. Technology has made it possible to make a virtue of necessity, with progress that in recent years has undergone a truly dizzying acceleration.

Oil was searched for the first time in water in 1938, at a depth of just 4 meters, with a few swimming strokes from Louisiana. The first really "offshore" well, 17 km off the same state, dates back to 1947: the platform was no bigger than a tennis court (the Deepwater Horizon had the size of a couple of football fields) and the crude was transported to land with barges taken by the Navy at the end of the Second World War.

It had to wait until the 1980s before Royal Dutch Shell managed to break the 1,000 foot deep (304.8 meter) threshold and up to 2000 to get to Macondo's 1.5 kilometer, with the Hoover Diana made by Saipem for ExxonMobil. Perdido - inaugurated last March 31 by Shell and capable of producing up to 100 thousand barrels of crude oil and 50 thousand cubic meters of gas per day - sinks its drills into the water for 3 km, more or less like five stacked Empire State Buildings.

But the real breakthrough in the offense is not only linked to the creation of increasingly powerful and sophisticated platforms, but to the new technologies for detecting the deposits, which allow to probe the depths, reconstructing images with three or even four dimensions of the potential deposits of hydrocarbons. This is how great discoveries have been made like that of Tupi, off the coast of Brazil, or Jubilee in the waters of Ghana. Discoveries that represent the future of oil. 
Read More → The challenge to Drill the depth of the New Offshore Wells

Thursday, March 21, 2019

Fire and Explosion Risk in Oil Gas Drilling

fire on offshore rig

There is always a risk of blowout when perforating a well, with a gas or vapour cloud release, followed by explosion and fire. Additional potential for fire and explosion exists in gas process operations.

Offshore platform and drilling rig workers should be carefully evaluated after having a thorough physical examination. The selection of offshore crew members with a history or evidence of pulmonary, cardiovascular or neurological diseases, epilepsy, diabetes, psychological disturbances and drug or alcohol addiction requires careful consideration. Because workers will be expected to use respiratory protection equipment and, in particular, those trained and equipped to fight fires, they must be physically and mentally evaluated for capability of carrying out these tasks. The medical examination should include psychological evaluation reflective of the particular job requirements.

Emergency medical services on offshore drilling rigs and production platforms should include provisions for a small dispensary or clinic, staffed by a qualified medical practitioner on board at all times. The type of medical service provided will be determined by the availability, distance and quality of the available onshore services. Evacuation may be by ship or helicopter, or a physician may travel to the platform or provide medical advice by radio to the onboard practitioner, when needed. A medical ship may be stationed where a number of large platforms operate in a small area, such as the North Sea, to be more readily available and quickly provide service to a sick or injured worker.

Persons not actually working on drilling rigs or platforms should also be given pre-employment and periodic medical examinations, particularly if they are employed to work in abnormal climates or under harsh conditions. These examinations should take into consideration the particular physical and psychological demands of the job.
Read More → Fire and Explosion Risk in Oil Gas Drilling

Wednesday, March 20, 2019

Working Conditions, Health and Safety in Oil Gas Frilling


Work on drilling rigs usually involves a minimum crew of 6 people (primary and secondary drillers, three assistant drillers or helpers (roughnecks) and a cat-head person) reporting to a site supervisor or foreman (tool pusher) who is responsible for the drilling progression. The primary and secondary drillers have overall responsibility for drilling operations and supervision of the drilling crew during their respective shifts. Drillers should be familiar with the capabilities and limitations of their crews, as work can progress only as fast as the slowest crew member.

Assistant drillers are stationed on the platform to operate equipment, read instruments and perform routine maintenance and repair work. The cathead person is required to climb up near the top of the derrick when drill pipe is being fed into or drawn out of the well hole and assist in moving the sections of pipe into and out of the stack. During drilling, the cathead person also operates the mud pump and provides general assistance to the drilling crew.

Persons who assemble, place, discharge and retrieve perforating guns should be trained, familiar with the hazards of explosives and qualified to handle explosives, primer cord and blasting caps. Other personnel working in and around oil fields include geologists, engineers, mechanics, drivers, maintenance personnel, electricians, pipeline operators and laborers.

Wells are drilled around the clock, on either 8- or 12-hour shifts, and workers require considerable experience, skill and stamina to meet the rigorous physical and mental demands of the job. Overextending a crew may result in a serious accident or injury. Drilling requires close teamwork and coordination in order to accomplish the tasks in a safe and timely fashion. Because of these and other requirements, consideration must be given to the morale and health and safety of workers. Adequate periods of rest and relaxation, nutritious food and appropriate hygiene and living quarters, including air conditioning in hot, humid climates and heating in cold-weather areas, are essential.

The primary occupational hazards associated with exploration and production operations include illnesses from exposure to geographical and climatic elements, stress from travelling long distances over water or harsh terrain and personal injury. Psychological problems may result from the physical isolation of exploratory sites and their remoteness from base camps and the extended work periods required on offshore drilling platforms and at remote onshore sites. Many other hazards particular to offshore operations, such as underwater diving, are covered elsewhere in this Encyclopedia.

Offshore work is dangerous at all times, both when on and off the job. Some workers cannot handle the stress of working offshore at a demanding pace, for extended periods of time, under relative confinement and subject to ever changing environmental conditions. The signs of stress in workers include unusual irritability, other signs of mental distress, excessive drinking or smoking and use of drugs. Problems of insomnia, which may be aggravated by high levels of vibration and noise, have been reported by workers on platforms. Fraternization among workers and frequent shore leave may reduce stress. Seasickness and drowning, as well as exposure to severe weather conditions, are other hazards in offshore work.

Illnesses such as respiratory tract diseases result from exposure to harsh climates, infections or parasitic diseases in areas where these are endemic. Although many of these diseases are still in need of epidemiological study in drilling workers, it is known that oil workers have experienced periarthritis of the shoulder and shoulder blade, humeral epicondylitis, arthrosis of the cervical spine and polyneuritis of the upper limbs. The potential for illnesses as a result of exposure to noise and vibration is also present in drilling operations. The severity and frequency of these drilling-related illnesses appears to be proportional to the length of service and exposure to adverse working conditions (Duck 1983; Ghosh 1983; Montillier 1983).

Injuries while working in drilling and production activities may result from many causes, including slips and falls, pipe handling, lifting pipe and equipment, misuse of tools and mishandling explosives. Burns may be caused by steam, fire, acid or mud containing chemicals such as sodium hydroxide. Dermatitis and skin injuries may result from exposure to crude oil and chemicals.

The possibility exists for acute and chronic exposure to a wide variety of unhealthful materials and chemicals which are present in oil and gas drilling and production. Some chemicals and materials which may be present in potentially hazardous amounts are listed in and include:

  • Crude oil, natural gas and hydrogen sulfide gas during drilling and blowouts
  • Heavy metals, benzene and other contaminants present in crude
  • Asbestos, formaldehyde, hydrochloric acid and other hazardous chemicals and materials


·     Normally occurring radioactive materials (NORMs) and equipment with radioactive sources.
Read More → Working Conditions, Health and Safety in Oil Gas Frilling

Tuesday, March 19, 2019

Natural Gas Production and Processing Operations

Offshore platform

There are two types of wells producing natural gas. Wet gas wells produce gas which contains dissolved liquids, and dry gas wells produce gas which cannot be easily liquefied

After natural gas is withdrawn from producing wells, it is sent to gas plants for processing. Gas processing requires a knowledge of how temperature and pressure interact and affect the properties of both fluids and gases. Almost all gas-processing plants handle gases that are mixtures of various hydrocarbon molecules. The purpose of gas processing is to separate these gases into components of similar composition by various processes such as absorption, fractionation and cycling, so they can be transported and used by consumers.

Absorption processes
Absorption involves three processing steps: recovery, removal and separation.

  • Recovery.

Removes undesirable residue gases and some methane by absorption from the natural gas. Absorption takes place in a counterflow vessel, where the well gas enters the bottom of the vessel and flows upward through absorption oil, which is flowing downward. The absorption oil is “lean” as it enters the top of the vessel, and “rich” as it leaves the bottom as it has absorbed the desirable hydrocarbons from the gas. The gas leaving the top of the unit is called “residue gas.”

Absorption may also be accomplished by refrigeration. The residue gas is used to pre-cool the inlet gas, which then passes through a gas chiller unit at temperatures from 0 to –40 °C. Lean absorber oil is pumped through an oil chiller, before contacting the cool gas in the absorber unit. Most plants use propane as the refrigerant in the cooler units. Glycol is injected directly into the inlet gas stream to mix with any water in the gas in order to prevent freezing and formation of hydrates. The glycol-water mixture is separated from the hydrocarbon vapour and liquid in the glycol separator, and then reconcentrated by evaporating the water in a regenerator unit.

  • Removal

The next step in the absorption process is removal, or demethanization. The remaining methane is removed from the rich oil in ethane recovery plants. This is usually a two-phase process, which first rejects at least one-half of the methane from the rich oil by reducing pressure and increasing temperature. The remaining rich oil usually contains enough ethane and propane to make reabsorption desirable. If not sold, the overhead gas is used as plant fuel or as a pre-saturator, or is recycled to the inlet gas in the main absorber.

  • Separation.

The final step in the absorption process, distillation, uses vapours as a medium to strip the desirable hydrocarbons from the rich absorption oil. Wet stills use steam vapours as the stripping medium. In dry stills, hydrocarbon vapours, obtained from partial vaporization of the hot oil pumped through the still reboiler, are used as the stripping medium. The still controls the final boiling point and molecular weight of the lean oil, and the boiling point of the final hydrocarbon product mix.

Other Processes

  • Fractionation.

Is the separation of the desirable hydrocarbon mixture from absorption plants, into specific, individual, relatively pure products. Fractionation is possible when the two liquids, called top product and bottom product, have different boiling points. The fractionation process has three parts: a tower to separate products, a reboiler to heat the input and a condenser to remove heat. The tower has an abundance of trays so that a lot of vapour and liquid contact occurs. The reboiler temperature determines the composition of the bottom product.

  • Sulphur recovery.

Hydrogen sulphide must be removed from gas before it is shipped for sale. This is accomplished in sulphur recovery plants.

  • Gas cycling.

Gas cycling is neither a means of pressure maintenance nor a secondary method of recovery, but is an enhanced recovery method used to increase production of natural gas liquids from “wet gas” reservoirs. After liquids are removed from the “wet gas” in cycling plants, the remaining “dry gas” is returned to the reservoir through injection wells. As the “dry gas” recirculates through the reservoir it absorbs more liquids. The production, processing and re circulation cycles are repeated until all of the recoverable liquids have been removed from the reservoir and only “dry gas” remains.
Read More → Natural Gas Production and Processing Operations

Thursday, March 14, 2019

Survey for Searching Oil and Gas

searching oil gas source for drilling
Sesmic Survey

The search for oil and gas requires a knowledge of geography, geology and geophysics. Crude oil is usually found in certain types of geological structures, such as anticlines, fault traps and salt domes, which lie under various terrains and in a wide range of climates. After selecting an area of interest, many different types of geophysical surveys are conducted and measurements performed in order to obtain a precise evaluation of the subsurface formations, including:

  • Magnetometric surveys. Magnetometers hung from airplanes measure variations in the earth’s magnetic field in order to locate sedimentary rock formations which generally have low magnetic properties when compared to other rocks.

  • Aerial photogrammetric surveys. Photographs taken with special cameras in airplanes, provide three-dimensional views of the earth which are used to determine land formations with potential oil and gas deposits.

  • Gravimetric surveys. Because large masses of dense rock increase the pull of gravity, gravimeters are used to provide information regarding underlying formations by measuring minute differences in gravity.

  • Seismic surveys. Seismic studies provide information on the general characteristics of the subsurface structure. Measurements are obtained from shock waves generated by setting off explosive charges in small-diameter holes, from the use of vibrating or percussion devices on both land and in water, and from underwater blasts of compressed air. The elapsed time between the beginning of the shock wave and the return of the echo is used to determine the depth of the reflecting substrata. The recent use of super-computers to generate three-dimensional images greatly improves evaluation of seismic test results.
  • Radiographic surveys. Radiography is the use of radio waves to provide information similar to that obtained from seismic surveys.
  • Stratigraphic surveys. Stratigraphic sampling is the analysis of cores of subsurface rock strata for traces of gas and oil. A cylindrical length of rock, called a core, is cut by a hollow bit and pushed up into a tube (core barrel) attached to the bit. The core barrel is brought to the surface and the core is removed for analysis.


When the surveys and measurements indicate the presence of formations or strata which may contain petroleum, exploratory wells are drilled to determine whether or not oil or gas is actually present and, if so, whether it is available and obtainable in commercially viable quantities.
Read More → Survey for Searching Oil and Gas

Properties of Hydrocarbon Gases - Drilling Knowledge

properties Hydrocarbon
Flaring Gas Testing

According to the US National Fire Protection Association, flammable (combustible) gases are those which burn in the concentrations of oxygen normally present in air. The burning of flammable gases is similar to that of flammable hydrocarbon liquid vapours, as a specific ignition temperature is needed to initiate the burning reaction and each will burn only within a certain defined range of gas-air mixtures. Flammable liquids have a flashpoint (the temperature (always below the boiling point) at which they emit sufficient vapours for combustion). There is no apparent flashpoint for flammable gases, as they are normally at temperatures above their boiling points, even when liquefied, and are therefore always at temperatures well in excess of their flashpoints.

The US National Fire Protection Association (1976) defines compressed and liquefied gases, as follows:

·     “Compressed gases are those which at all normal atmospheric temperatures inside their containers, exist solely in the gaseous state under pressure.”

·     “Liquefied gases are those which at normal atmospheric temperatures inside their containers, exist partly in the liquid state and partly in the gaseous state, and are under pressure as long as any liquid remains in the container.”

The major factor which determines the pressure inside the vessel is the temperature of the liquid stored. When exposed to the atmosphere, the liquefied gas very rapidly vaporizes, travelling along the ground or water surface unless dispersed into the air by wind or mechanical air movement. At normal atmospheric temperatures, about one-third of the liquid in the container will vaporize.

Flammable gases are further classified as fuel gas and industrial gas. Fuel gases, including natural gas and liquefied petroleum gases (propane and butane), are burned with air to produce heat in ovens, furnaces, water heaters and boilers. Flammable industrial gases, such as acetylene, are used in processing, welding, cutting and heat treating operations.
Read More → Properties of Hydrocarbon Gases - Drilling Knowledge

Compressed Natural Gas and Liquefied Hydrocarbon Gases

Hydrocarbon Gases
LNG

The composition of naturally occurring hydrocarbon gases is similar to crude oils in that they contain a mixture of different hydrocarbon molecules depending on their source. They can be extracted as natural gas (almost free of liquids) from gas fields; petroleum-associated gas which is extracted with oil from gas and oil fields; and gas from gas condensate fields, where some of the liquid components of oil convert into the gaseous state when pressure is high (10 to 70 mPa). When the pressure is decreased (to 4 to 8 mPa) condensate containing heavier hydrocarbons separates from the gas by condensation. Gas is extracted from wells reaching up to 4 miles (6.4 km) or more in depth, with seam pressures varying from 3 mPa up to as high as 70 mPa.

Natural gas contains 90 to 99% hydrocarbons, which consist predominately of methane (the simplest hydrocarbon) together with smaller amounts of ethane, propane and butane. Natural gas also contains traces of nitrogen, water vapour, carbon dioxide, hydrogen sulphide and occasional inert gases such as argon or helium. Natural gases containing more than 50 g/m3 of hydrocarbons with molecules of three or more carbon atoms (C3 or higher) are classified as “lean” gases.

Depending how it is used as a fuel, natural gas is either compressed or liquefied. Natural gas from gas and gas condensate fields is processed in the field to meet specific transportation criteria before being compressed and fed into gas pipelines. This preparation includes removal of water with driers (dehydrators, separators and heaters), oil removal using coalescing filters, and the removal of solids by filtration. Hydrogen sulphide and carbon dioxide are also removed from natural gas, so that they do not corrode pipelines and transportation and compression equipment. Propane, butane and pentane, present in natural gas, are also removed before transmission so they will not condense and form liquids in the system. (See the section “Natural gas production and processing operations.”)

Natural gas is transported by pipeline from gas fields to liquefication plants, where it is compressed and cooled to approximately –162 °C to produce liquefied natural gas (LNG). The composition of LNG is different from natural gas due to the removal of some impurities and components during the liquefaction process. LNG is primarily used to augment natural gas supplies during peak demand periods and to supply gas in remote areas away from major pipelines. It is regasified by adding nitrogen and air to make it comparable to natural gas before being fed into gas supply lines. LNG is also used as a motor-vehicle fuel as an alternative to gasoline.

Petroleum-associated gases and condensate gases are classified as “rich” gases, because they contain significant amounts of ethane, propane, butane and other saturated hydrocarbons. Petroleum-associated and condensate gases are separated and liquefied to produce liquefied petroleum gas (LPG) by compression, adsorption, absorption and cooling at oil and gas process plants. These gas plants also produce natural gasoline and other hydrocarbon fractions.

Unlike natural gas, petroleum-associated gas and condensate gas, oil processing gases (produced as by-products of refinery processing) contain considerable amounts of hydrogen and unsaturated hydrocarbons (ethylene, propylene and so on). The composition of oil processing gases depends upon each specific process and the crude oils used. For example, gases obtained as a result of thermal cracking usually contain significant amounts of olefins, while those obtained from catalytic cracking contain more isobutanes. Pyrolysis gases contain ethylene and hydrogen.

Combustible natural gas, with a calorific value of 35.7 to 41.9 MJ/m3 (8,500 to 10,000 kcal/m3), is primarily used as a fuel to produce heat in domestic, agricultural, commercial and industrial applications. The natural gas hydrocarbon also is used as feedstock for petrochemical and chemical processes. Synthesis gas (CO + H2) is processed from methane by oxygenation or water vapour conversion, and used to produce ammonia, alcohol and other organic chemicals. Compressed natural gas (CNG) and liquefied natural gas (LNG) are both used as fuel for internal combustion engines. Oil processing liquefied petroleum gases (LPG) have higher calorific values of 93.7 MJ/m3 (propane) (22,400 kcal/m3) and 122.9 MJ/m3 (butane) (29,900 kcal/m3) and are used as fuel in homes, businesses and industry as well as in motor vehicles (NFPA 1991). The unsaturated hydrocarbons (ethylene, propylene and so on) derived from oil processing gases may be converted into high-octane gasoline or used as raw materials in the petrochemical and chemical-processing industries.
Read More → Compressed Natural Gas and Liquefied Hydrocarbon Gases

Composition of Crude oil and Natural gas in Drilling


Relatively simple crude-oil assays are used to classify crude oils as paraffinic, naphthenic, aromatic or mixed, based on the predominant proportion of similar hydrocarbon molecules. Mixed-base crudes have varying amounts of each type of hydrocarbon. One assay method (US Bureau of Mines) is based on distillation, and another method (UOP "K" factor) is based on gravity and boiling points. More comprehensive crude assays are conducted to determine the value of the crude (i.e., its yield and quality of useful products) and processing parameters. Crude oils are usually grouped according to yield structure, with high-octane gasoline being one of the more desirable products. Refinery crude oil feedstocks usually consist of mixtures of two or more different crude oils.

Crude oils are also defined in terms of API (specific) gravity. For example, heavier crude oils have low API gravitates (and high specific gravities). A low-API gravity crude oil may have either a high or low flash point, depending on its lightest ends (more volatile constituents). Because of the importance of temperature and pressure in the refining process, crude oils are further classified as to viscosity, pour points and boiling ranges. Other physical and chemical characteristics, such as color and carbon residue content, are also considered. Crude oils with high carbon, low hydrogen and low API gravity are usually rich in aromatics; while those with low carbon, high hydrogen and high API gravity are usually rich in paraffin.

Crude oils which contain appreciable quantities of hydrogen sulfide or other reactive sulphur compounds are called “sour.” Those with less sulphur are called “sweet.” Some exceptions to this rule are West Texas crude (which are always considered “sour” regardless of their H2S content) and Arabian high-sulfur crudes (which are not considered “sour” because their sulfur compounds are not highly reactive).

Hidrocarbon:

Paraffins: The paraffinic saturated chain type hydrocarbon (aliphatic) molecules in crude oil have the formula CnH2n+2, and can be either straight chains (normal) or branched chains (isomers) of carbon atoms. The lighter, straight chain paraffin molecules are found in gases and paraffin waxes. The branched chain paraffins are usually found in heavier fractions of crude oil and have higher octane numbers than normal paraffins.

Aromatics: Aromatics are unsaturated ring type hydrocarbon (cyclic) compounds. Naphthalenes are fused double ring aromatic compounds. The most complex aromatics, polynuclears (three or more fused aromatic rings), are found in heavier fractions of crude oil.

Naphthenes: Naphthenes are saturated ring type hydrocarbon groupings, with the formula CnH2n, arranged in the form of closed rings (cyclic), found in all fractions of crude oil except the very lightest. Single ring naphthenes (mono-cycloparaffins) with 5 and 6 carbon atoms predominate, with two ring naphthenes (dicycloparaffins) found in the heavier ends of naphtha.

Non-hydrocarbons

Sulphur or sulfur and sulphur compounds: Sulphur is present in natural gas and crude oil as hydrogen sulphide (H2S), as compounds (thiols, mercaptans, sulphides, polysulphides, etc.) or as elemental sulphur. Each gas and crude oil has different amounts and types of sulphur compounds, but as a rule the proportion, stability and complexity of the compounds are greater in heavier crude oil fractions.

Sulphur compounds called mercaptans, which exhibit distinct odours detectable at very low concentrations, are found in gas, petroleum crude oils and distillates. The most common are methyl and ethyl mercaptans. Mercaptans are often added to commercial gas (LNG and LPG) to provide an odour for leak detection.

The potential for exposure to toxic levels of H2S exists when working in drilling, production, transportation and processing crude oil and natural gas. The combustion of petroleum hydrocarbons containing sulphur produces undesirables such as sulphuric acid and sulphur dioxide.

Oxygen compounds: Oxygen compounds, such as phenols, ketones and carboxylic acids, are found in crude oils in varying amounts.

Nitrogen compounds: Nitrogen is found in lighter fractions of crude oil as basic compounds, and more often in heavier fractions of crude oil as non-basic compounds which may also include trace metals.

Trace metals: Trace amounts, or small quantities of metals, including copper, nickel, iron, arsenic and vanadium, are often found in crude oils in small quantities.

Inorganic salts: Crude oils often contain inorganic salts, such as sodium chloride, magnesium chloride and calcium chloride, suspended in the crude or dissolved in entrained water (brine).

Carbon dioxide: Carbon dioxide may result from the decomposition of bicarbonates present in, or added to crude, or from steam used in the distillation process.

Naphthenic acids: Some crude oils contain naphthenic (organic) acids, which may become corrosive at temperatures above 232 °C when the acid value of the crude is above a certain level.

Normally occurring radioactive materials: Normally occurring radioactive materials (NORMs) are often present in crude oil, in the drilling deposits and in the drilling mud, and can present a hazard from low levels of radioactivity.
Read More → Composition of Crude oil and Natural gas in Drilling

Sunday, March 10, 2019

Drillling Geothermal Well with Laser

laser

From fossil fuels to geothermal heat, accessing the planet’s energy riches usually involves boring deep into the Earth with giant metal drills. But could lasers do the same job?

Foro Energy, a start-up company in Littleton, Colorado, has developed what it claims is an inexpensive system of high-powered lasers that can rip through rock, potentially revolutionising drilling and hastening the adoption of greener forms of power.

Foro announced last month that a test system had sent a beam from a 20-kilowatt commercial laser through 1.5 kilometres of optical fibre. Development has been funded by the US Department of Energy’s research arm, ARPA-E. Borehole drilling trials are planned for next year.

Mechanical drills can easily grind through soft rocks like sandstone to tap petroleum reserves, but they wear out quickly in hard crystalline rocks such as granite and basalt. It is these harder rocks that often hide the best sources of geothermal energy. Foro’s intense laser beam heats hard rock surfaces so fast that thermal shock fractures the upper few millimetres, leaving a crumbled layer that a mechanical drill can scrape away quickly and with little wear. This approach could increase drilling rates, a major component in well cost, by up to a factor of 10, says ARPA-E.

But a flashy prototype is far from proof that the rig will hold up in the brutal environment found in the bottom of a borehole, which is filled with rock chips and churning water that lubricates the drill bit. The optics must deliver the beam directly to the rock, says Jared Potter of Potter Drilling in Redwood City, California, who is developing a drilling process that shatters rock with extremely hot water. If the beam hits fluid, it will heat the liquid instead of the rock face. “It’s amazing how much energy it takes to boil water,” Potter says, and even a powerful laser couldn’t hope to zap both water and rock at once. He thinks Foro “has a long way to go to have a tool they can deploy in a geothermal or oil well”.

Still, the cost of drilling has been a roadblock to expanding the adoption of geothermal energy. If Foro can prove its technology is ready for the grunt work of punching hundreds of holes through the hard igneous rocks, it would change the mathematics of low-carbon energy. In the meantime, Potter says Foro’s lasers could be used instead of explosives to make holes in the steel casings of oil and gas wells, which are needed to drain fluid from the surrounding rock.

Read More → Drillling Geothermal Well with Laser

CEMENTING ADDITIVES CHEMICAL

chemical for well drilling
Cementing Additive Chemical

Additional chemicals are used to control slurry density, rheology, and fluid loss, or to provide
more specialized slurry properties. Additives modify the behavior of the cement slurry allowing cement placement under a wide range of downhole conditions. There are many additives available for cement and these can be classified under one of the following categories:

Accelerators: Most operators wait for cement to reach a minimum compressive strength of 500 psi before resuming operations. At temperatures below l00 °F common cement may require a day or two to develop this strength level. chemicals which reduce the thickening time of a slurry and increase the rate of early strength development. Low concentrations of cement accelerators (2-4% by weight of cement) are used to shorten the setting time of cement and promote rapid strength development.They are usually use in conductor and surface casing to reduce waiting on cement time (WOC). Calcium chloride (CaCl2), sodium chloride (NaCl) and sea water are commonly used as accelerators.

Retarders: chemicals which retard the setting time (extend the thickening) of a slurry to aid cement placement before it hardens. Retarders Increased well depths and formation temperatures require the use of cement retarders to extend the pumpability of cements. Most retarders also affect cement viscosity to some extent..These additives are usually added to counter the effects of high temperature.They are used in cement slurries for intermediate and production casings, squeeze and cement plugs and high temperature wells. Typical retarders include: sugar; lignosulphonates, hydroxycarboxylic acids, inorganic compounds and cellulose derivatives.

Retarders work mainly by adsorption on the cement surface to inhibit contact with water and
elongate the hydration process; although there are other chemical mechanisms involved.

Lignosulfonates are used to about 200°F bottom-hole circulating temperature (BHCT). Concentrations of 0.1% to 1% are used in most slurry applications to give both predictable thickening times and compressive strength.

Organic acids can be used from about 200°-400°F BHCT. They are used on concentrations of 0.1% to 2.5% by weight of cement as effective retarders for high temperature environments.

Extenders: materials which lower the slurry density and increase the yield to allow weak
formations to be cemented without being fractured by the cement cloumn.Examples of
extenders include: water, bentonite, sodium silicates, pozzlans, gilsonite, expanded perlite,
nitrogen and ceramic microspheres. Bentonite clay can be used in concentrations up to 25%
by weight of Portland cement to decrease the density.

Weighting Agents (density adjusters): materials which increase slurry density including barite and haematite High-density slurries are used to cement high-pressure wells where increased hydrostatic head is required to hold down gas or fluids. 

- Hematite, sp. gr. of 5, is used to increase slurry density to 21 1b/gal. Barite, sp. gr. 4.2 can
increase slurry weight to 18Ib/gal.

- Sand, sp.gr. 2.65, has a low water requirement and helps to densify slurries to 17.5Ib/gal.

Dispersants: chemicals which lower the slurry viscosity and may also increase free water by dispersing the solids in the cement slurry. Dispersants are solutions of negatively charged polymer molecules that attach themselves to the positively charges sites of the hydrating cement grains.The result is an increased negative on the hydrating cement grains resulting in greater repulsive forces and particle dispersion.

The most common dispersants are aryl-alkyl sulphonates used in concentrations of 0.3% to 2% by weight of cement polyphosphate, lignosulfonate, salt and organic acid.

Fluid-Loss Additives: Excessive fluid losses from the cement slurry to the formation can affect the correct setting of cement. Fluid loss additives are used to prevent slurry dehydration and reduce fluid loss to the formation.Examples include: cationic polymer, nonionic synthetic polymer, anionic synthetic polymer and cellulose derivative.

Lost Circulation Control Agents: materials which control the loss of cement slurry to weak or fractured formations.

Strength Retrogression: At temperatures above 230 F, normal cement develop high permeability and reduction in strength. the addition of 30-40% BWOC (by weight of cement) silica flour prevents both strength reduction and development of permeability at high temperatures.

Miscellaneous Agents: e.g. Anti-foam agents, fibres, latex.
Read More → CEMENTING ADDITIVES CHEMICAL

TYPES OF CASING PIPE

oil gas casing pipe for drilling
Casing Pipe for Oil Gas Well

In practice, it would be much cheaper to drill a hole to total depth (TD), probably with a small
diameter drill bit, and then case the hole from surface to TD. However, the presence of high pressured zones at different depths along the wellbore, and the presence of weak, unconsolidated formations or sloughing, shaly zones, necessitates running casing to seal off these troublesome zones and to allow the drilling to TD. Thus, different sizes of casing are employed and this arrangement gives a tapered shape to the finished well. 

The types of casing currently in use are as follows:
  1. Stove Pipe

Stove pipe (or marine-conductor, or foundation-pile for offshore drilling) is run to prevent washouts of near-surface unconsolidated formations, to provide a circulation system for the drilling mud and to ensure the stability of the ground surface upon which the rig is sited. This pipe does not usually carry any weight from the wellhead equipment and can be driven into the ground or seabed with a pile driver. A typical size for a stove pipe ranges from 26 in. to 42 in.

    2. Conductor Pipe

Conductor pipe is run from the surface to a shallow depth to protect near surface unconsolidated formations, seal off shallow-water zones, provide protection against shallow gas flows, and provide a conduit for the drilling mud. One or more BOPs may be mounted on this casing or a diverter system if the setting depth of the conductor pipe is shallow. In the Middle East, a typical size for a conductor pipe is either 18 5/8 in. (473 mm) or 20 in. (508 mm). In North Sea exploration wells, the size of the conductor pipe is usually 26 or 30 in also in most of Iraqi wells. Conductor pipe is always cemented to surface. It is used to support subsequent casing strings and wellhead equipment or alternatively the pipe is cut off at the surface after setting the surface casing.

 3. Surface Casing

Surface casing is run to prevent caving of weak formations that are encountered at shallow
depths. This casing should be set in competent rocks such as hard limestone. This will ensure that formations at the casing shoe will not fracture at the high hydrostatic pressures which may be encountered later. The surface casing also serves to provide protection against shallow blowouts, hence BOPs are connected to the top of this string. The setting depth of this casing string is chosen so that troublesome formations, thief zones, water sands, shallow hydrocarbon zones and build-up sections of deviated wells may be protected. A typical size of this casing is l3 3/8 in. (240 mm) in the Middle East and 18 5/8 in. or 20 in. in North Sea operations.

4. Production Casing

Production casing is the last casing string. It is run to isolate producing zones, to provide reservoir fluid control and to permit selective production in multizone production. This is the string through which the well will be completed. The usual sizes of this string are 4 1/2, 5 and 7 in.

6. Liners

A liner is a string of casing that does not reach the surface. Liners are hung on the intermediate casing by use of a liner-hanger. In liner completions both the liner and the intermediate casing act as the production string. Because a liner is set at the bottom and hung from the intermediate casing, the major design criterion for a liner is usually the ability to withstand the maximum expected collapse pressure.
Read More → TYPES OF CASING PIPE

PDC BITS APPLICATIONS

type of bit for drilling oil gas well
PDC Bit

PDC bits have been used extensively and successfully over a wide range of formation types. The lack of rotating parts leads to greater life expectancy and as such long bit runs are achievable with resultant time and cost savings. A thorough review of the economics of running a PDC bit needs to be performed prior to selection due to its increased cost. 

The following guidelines list the typical applications of PDC bits.
  1. PDC bits are typically useful for drilling long, soft to medium shale sequences which have a low abrasivity. In such formations they typically exhibit high ROP and extended life enabling entire sections to be drilled on one run.
  2. PDC bits are not usually appropriate for highly abrasive well cemented sand sequences.When drilling tight siliceous formations the incidence of PDC chipping and breaking is dramatically increased resulting in less than expected ROP and bit life.
  3. When drilling heterogeneous formations containing alternating shales and or shale limestone sequences the use of hybrid PDC bits is encouraged. This bit incorporates the use of back-up diamond studs behind the PDC cutter. When drilling harder abrasive strings, the diamond stud absorbs the increased weight required to drill the stringer and prevents premature damage and wear to the PDC cutter.
  4. The use of bladed hybrid PDC bits is recommended for drilling hard formations. The deep watercourse on these bits enable optimum fluid flow across the cutter to efficiently reduce the friction temperatures induced. This efficient cooling will help minimise fracture of the PDC cutters.
  5. When drilling mobile, plastic formations such as salt sections the use of eccentric PDC bits should be considered. These bits have proved successful in preventing incidence of stuck pipe in many areas where salt flow problems are experienced.
Read More → PDC BITS APPLICATIONS

Saturday, March 9, 2019

WASHOUTS IN DRILLSTRINGS


Tool joint failure is one of the main causes of fishing jobs in the drilling industry. This failure is due entirely to the tool joint threads not holding or not being made properly. The make up torque puts the pin in tension and the box in compression, see Figure below. If the pin and box are not properly torqued, then the seals may separate under downhole conditions allowing the a leak path for the mud.

Each drillpipe joint has a pin and a box. Hence for a length of 1000 ft of drillstring there are 66 separate pins and boxes that need to mad up and broken regularly. The threads of the tooljoints seal at the shoulder area only. This feature requires that enough torque is applied during makeup to reduce the risk of having a loose connection in the drillstring. Leak paths within the tool joints develop if the seal is broken or if improper torque is applied. The leak path will lead to tool joint erosion by the drilling mud and if this erosion is severe enough that causes the surface of the pipe to be broken, the pipe is said to have a "washout".

Washouts can also develop due to cracks developing within the drillpipe due to severe drilling vibrations or cyclic loading, Figure below This is especially true in drillstrings rotating at RPM’s matching the drillstring natural (harmonic) frequencies. Washouts are usually detected by a decrease in the standpipe pressure, between 100 -300 psi over 5-15 minutes. This is easily distinguished from sudden drops in pump pressure which could be due to a lost jet nozzle or some surface leak. If a decrease in pump pressure is seen at surface, drilling should stop, pumping resumed. If the pump pressure is still less than before and a bit jet is not suspected to have been lost or no surface leaks detected, then the drillstring should be pulled out of a hole and the defective drillpipe joint should be replaced. Drilling records show that in some cases when a washout is suspected and the pipe was POH (pull out of hole), no cracks or washouts could be visibly seen on any of the drillpipe joints. The reason that the cracks could not been seen at surface is that under pumping and drilling conditions, the cracks open letting mud out and reduce the pump pressure requirements. When at surface, however, the drillpipe is under zero tension and the cracks therefore close escaping detection by the observer on the rig floor.

The author has come across several such situations when a washout is detected and when the drillstring POH, no defective pipe is seen. When the drillstring is re-run in hole, the pump pressure was still lower than before and in some cases it continued to drop. If drilling was resumed a twist off usually occurs resulting in a fishing job. To overcome this, it has been found useful in practice to pump a soft plastic line prior to POH. The soft line wedges itself into the crack(s) while the pipe is still down hole and whilst pumping, Figure below When the pipe is POH to surface, the defective drillpipe joint is easily noticed by the presence of the soft plastic line in the cracks.
Read More → WASHOUTS IN DRILLSTRINGS

Friday, March 8, 2019

Multilateral Drilling

multi lateral hole drilling oil gas
Multilateal Drilling

Sometimes oil and natural gas reserves are located in separate layers underground and multilateral drilling allows producers to branch out from the main well to tap reserves at different depths.

This increases production from a single well and reduces the number of wells drilled on the surface.

A multilateral well is a single well with one or more wellbore branches radiating from the main borehole.

It may be an exploration well, an infill development well or a reentry into an existing well.

It may be as simple as a vertical wellbore with one sidetrack or as complex as a horizontal, extended-reach well with multiple lateral and sublateral branches.

General multi- lateral configurations include:

  • Multibranched wells, forked wells, wells with several laterals branching from one horizontal main wellbore, wells with several laterals branching from one vertical main wellbore, wells with stacked laterals, and wells with dual-opposing laterals.


These wells generally represent two basic types:

vertically staggered laterals and horizontally spread laterals in fan, spine-and-rib or dual-opposing T shapes.

A successful multilateral well that replaces several vertical wellbores can reduce overall drilling and completion costs, increase production and provide more efficient drainage of a reservoir. Furthermore, multilaterals can make reservoir management more efficient and help increase recoverable reserves.

Regardless of the level of complexity, multi- lateral wells today are drilled with state-of-the art directional drilling technology, but there is always a certain risks ranging from borehole instability, stuck pipe and problems with overpressured zones to casing, cementing and branching problems.

Advantages of multilateral systems increasingly outweigh the disadvantages.

Multilateral wells configuration enhance productivity.

In shallow or depleted reservoirs, branched horizontal wellbores are often most efficient, whereas in layered reservoirs, vertically stacked drainholes are usually best.

In fractured reservoirs, dual-opposing laterals may provide maximum reservoir exposure, particularly when fracture orientation is known (From Schlumberger Oilfield review)
Read More → Multilateral Drilling