Showing posts with label drilling chemical. Show all posts
Showing posts with label drilling chemical. Show all posts

Sunday, March 10, 2019

CEMENTING ADDITIVES CHEMICAL

chemical for well drilling
Cementing Additive Chemical

Additional chemicals are used to control slurry density, rheology, and fluid loss, or to provide
more specialized slurry properties. Additives modify the behavior of the cement slurry allowing cement placement under a wide range of downhole conditions. There are many additives available for cement and these can be classified under one of the following categories:

Accelerators: Most operators wait for cement to reach a minimum compressive strength of 500 psi before resuming operations. At temperatures below l00 °F common cement may require a day or two to develop this strength level. chemicals which reduce the thickening time of a slurry and increase the rate of early strength development. Low concentrations of cement accelerators (2-4% by weight of cement) are used to shorten the setting time of cement and promote rapid strength development.They are usually use in conductor and surface casing to reduce waiting on cement time (WOC). Calcium chloride (CaCl2), sodium chloride (NaCl) and sea water are commonly used as accelerators.

Retarders: chemicals which retard the setting time (extend the thickening) of a slurry to aid cement placement before it hardens. Retarders Increased well depths and formation temperatures require the use of cement retarders to extend the pumpability of cements. Most retarders also affect cement viscosity to some extent..These additives are usually added to counter the effects of high temperature.They are used in cement slurries for intermediate and production casings, squeeze and cement plugs and high temperature wells. Typical retarders include: sugar; lignosulphonates, hydroxycarboxylic acids, inorganic compounds and cellulose derivatives.

Retarders work mainly by adsorption on the cement surface to inhibit contact with water and
elongate the hydration process; although there are other chemical mechanisms involved.

Lignosulfonates are used to about 200°F bottom-hole circulating temperature (BHCT). Concentrations of 0.1% to 1% are used in most slurry applications to give both predictable thickening times and compressive strength.

Organic acids can be used from about 200°-400°F BHCT. They are used on concentrations of 0.1% to 2.5% by weight of cement as effective retarders for high temperature environments.

Extenders: materials which lower the slurry density and increase the yield to allow weak
formations to be cemented without being fractured by the cement cloumn.Examples of
extenders include: water, bentonite, sodium silicates, pozzlans, gilsonite, expanded perlite,
nitrogen and ceramic microspheres. Bentonite clay can be used in concentrations up to 25%
by weight of Portland cement to decrease the density.

Weighting Agents (density adjusters): materials which increase slurry density including barite and haematite High-density slurries are used to cement high-pressure wells where increased hydrostatic head is required to hold down gas or fluids. 

- Hematite, sp. gr. of 5, is used to increase slurry density to 21 1b/gal. Barite, sp. gr. 4.2 can
increase slurry weight to 18Ib/gal.

- Sand, sp.gr. 2.65, has a low water requirement and helps to densify slurries to 17.5Ib/gal.

Dispersants: chemicals which lower the slurry viscosity and may also increase free water by dispersing the solids in the cement slurry. Dispersants are solutions of negatively charged polymer molecules that attach themselves to the positively charges sites of the hydrating cement grains.The result is an increased negative on the hydrating cement grains resulting in greater repulsive forces and particle dispersion.

The most common dispersants are aryl-alkyl sulphonates used in concentrations of 0.3% to 2% by weight of cement polyphosphate, lignosulfonate, salt and organic acid.

Fluid-Loss Additives: Excessive fluid losses from the cement slurry to the formation can affect the correct setting of cement. Fluid loss additives are used to prevent slurry dehydration and reduce fluid loss to the formation.Examples include: cationic polymer, nonionic synthetic polymer, anionic synthetic polymer and cellulose derivative.

Lost Circulation Control Agents: materials which control the loss of cement slurry to weak or fractured formations.

Strength Retrogression: At temperatures above 230 F, normal cement develop high permeability and reduction in strength. the addition of 30-40% BWOC (by weight of cement) silica flour prevents both strength reduction and development of permeability at high temperatures.

Miscellaneous Agents: e.g. Anti-foam agents, fibres, latex.
Read More → CEMENTING ADDITIVES CHEMICAL

Friday, March 8, 2019

Drilling Fluid Functions




The following is the function of Drilling Fluid: 

  1. Cool the drill bit and lubricates its teeth: one of the prime functions of the drilling fluid or mud is to cool the drill bit and lubricate its teeth. The drilling action requires a considerable amount of mechanical energy in the form of weight on bit, rotation, and hydraulic energy. A large proportion of this energy is dissipated as heat, which must be remove to allow the drill bit to function properly, the drilling mud also helps the removing of the rock cuttings from the space between the bit teeth, thereby preventing bit balling which is one of the common problems in drilling process. 
  2. Lubricates and cool the drillstring: a rotary drillstring generates a considerable amount of heat which must be dissipated outside the hole. The drilling mud helps to cool the drillstring by absorbing the heat and releasing it, by convection and radiation, to air surrounding the surface mud tanks (pits). The mud also, provides lubrication by reducing friction between drillstring and borehole walls. Lubrication is usually achieved by the addition of bentonite, oil, graphite, etc.
  3. Control formation pressure: for safe drilling, high formation pressure must be contained within the hole to prevent damage to equipment and injury to personnel. The drilling mud achieves this by providing a hydrostatic pressure just greater than the formation pressure. For effective drilling, the difference between the hydrostatic pressure and formation pressure should be zero. the hydrostatic pressure depends on the mud weight which, in turn, depends on the type of solids added to the fluid making up the mud and the density of the continuous phase. In practice, an overbalance,(Where the pressure in the wellbore in higher than the pressure in the formation), 100 to 200 psi (trip margin) is normally used to provide an adequate safe guard against well kick. The pressure overbalance sometimes referred to as chip hold down pressure (CHDP), and its value directly influences penetration rate. In general, penetration rate decreases as (CHDP) increases. When an abnormally pressured formation is encountered, the (CHDP) becomes negative and sudden increase in penetration rate is observed. This is normally taken as an indication of a well kick.
  4. Carry cuttings out of the hole: for effective drilling, cuttings generated by the bit must be removed immediately. The drilling mud carries these cuttings up the hole and to the surface, to be separated from the mud. The removal of cuttings depends on the viscous properties called "Yield Point" which influences the carrying capacity of the flowing mud and "gels" which help to keep the cuttings in suspension when the mud is static to prevent them from accumulating on the bottom of the hole and causing pipe sticking. The flow rate of mud is also critical in cleaning the hole.
  5. Stabilize the wellbore and prevent it from caving in: the formation of a good mud cake helps to stabilize the walls of plaster to interior walls (like plastering a room walls to keep them from flaking). The pressure differential between hydrostatic pressure of mud and that of the wellbore stable. Shale stability is largely dependent on the type of mud used To minimise the swelling stresses caused by the reaction of the mud with the shale formations. This reaction can cause hole erosion or cavings resulting in an unstable wellbore. Minimisation of wellbore instability is provided by the "inhibition" character of the drilling mud.. At last it should be noted that the best way to keep a hole stable is to reduce time during which the hole is kept open.
  6. Helps in the evaluation and interpretation of well logs: wire line logs are run in mud-fills holes in order to ascertain the existence and size of hydrocarbons zones. Open hole logs are also run to determine porosity, boundaries between formations, location of geopressured (or abnormally pressured) formations and the site for the next well. Hence, the drilling mud must possess such properties that it will aid the production of good logs (Log response may be enhanced through selection of specific fluids and conversely, use of a given fluid may eliminate a log from use. Drilling fluids must be evaluated to assure compatibility with the logging program).
  7. Limiting the corrosion of drilling equipment: the drilling mud in most cases will have water that contains dissolved salts as its base liquid. This serves as a medium in which corrosion takes place. If corrosion is suspected, then the cause should be determined and steps taken to prevent damage of the equipment. It has been found that in muds containing oil as the continuous phase, little or no corrosion occurs.
  8. Transmit Hydraulic Horsepower to Bit: Hydraulic horsepower generated at the bit is the result of flow volume and pressure drop through the bit nozzles. This energy is converted into mechanical energy which removes cuttings from the bottom of the hole and improves the rate of penetration.
Read More → Drilling Fluid Functions