Thursday, March 14, 2019

Properties of Hydrocarbon Gases - Drilling Knowledge

properties Hydrocarbon
Flaring Gas Testing

According to the US National Fire Protection Association, flammable (combustible) gases are those which burn in the concentrations of oxygen normally present in air. The burning of flammable gases is similar to that of flammable hydrocarbon liquid vapours, as a specific ignition temperature is needed to initiate the burning reaction and each will burn only within a certain defined range of gas-air mixtures. Flammable liquids have a flashpoint (the temperature (always below the boiling point) at which they emit sufficient vapours for combustion). There is no apparent flashpoint for flammable gases, as they are normally at temperatures above their boiling points, even when liquefied, and are therefore always at temperatures well in excess of their flashpoints.

The US National Fire Protection Association (1976) defines compressed and liquefied gases, as follows:

·     “Compressed gases are those which at all normal atmospheric temperatures inside their containers, exist solely in the gaseous state under pressure.”

·     “Liquefied gases are those which at normal atmospheric temperatures inside their containers, exist partly in the liquid state and partly in the gaseous state, and are under pressure as long as any liquid remains in the container.”

The major factor which determines the pressure inside the vessel is the temperature of the liquid stored. When exposed to the atmosphere, the liquefied gas very rapidly vaporizes, travelling along the ground or water surface unless dispersed into the air by wind or mechanical air movement. At normal atmospheric temperatures, about one-third of the liquid in the container will vaporize.

Flammable gases are further classified as fuel gas and industrial gas. Fuel gases, including natural gas and liquefied petroleum gases (propane and butane), are burned with air to produce heat in ovens, furnaces, water heaters and boilers. Flammable industrial gases, such as acetylene, are used in processing, welding, cutting and heat treating operations.
Read More → Properties of Hydrocarbon Gases - Drilling Knowledge

Compressed Natural Gas and Liquefied Hydrocarbon Gases

Hydrocarbon Gases
LNG

The composition of naturally occurring hydrocarbon gases is similar to crude oils in that they contain a mixture of different hydrocarbon molecules depending on their source. They can be extracted as natural gas (almost free of liquids) from gas fields; petroleum-associated gas which is extracted with oil from gas and oil fields; and gas from gas condensate fields, where some of the liquid components of oil convert into the gaseous state when pressure is high (10 to 70 mPa). When the pressure is decreased (to 4 to 8 mPa) condensate containing heavier hydrocarbons separates from the gas by condensation. Gas is extracted from wells reaching up to 4 miles (6.4 km) or more in depth, with seam pressures varying from 3 mPa up to as high as 70 mPa.

Natural gas contains 90 to 99% hydrocarbons, which consist predominately of methane (the simplest hydrocarbon) together with smaller amounts of ethane, propane and butane. Natural gas also contains traces of nitrogen, water vapour, carbon dioxide, hydrogen sulphide and occasional inert gases such as argon or helium. Natural gases containing more than 50 g/m3 of hydrocarbons with molecules of three or more carbon atoms (C3 or higher) are classified as “lean” gases.

Depending how it is used as a fuel, natural gas is either compressed or liquefied. Natural gas from gas and gas condensate fields is processed in the field to meet specific transportation criteria before being compressed and fed into gas pipelines. This preparation includes removal of water with driers (dehydrators, separators and heaters), oil removal using coalescing filters, and the removal of solids by filtration. Hydrogen sulphide and carbon dioxide are also removed from natural gas, so that they do not corrode pipelines and transportation and compression equipment. Propane, butane and pentane, present in natural gas, are also removed before transmission so they will not condense and form liquids in the system. (See the section “Natural gas production and processing operations.”)

Natural gas is transported by pipeline from gas fields to liquefication plants, where it is compressed and cooled to approximately –162 °C to produce liquefied natural gas (LNG). The composition of LNG is different from natural gas due to the removal of some impurities and components during the liquefaction process. LNG is primarily used to augment natural gas supplies during peak demand periods and to supply gas in remote areas away from major pipelines. It is regasified by adding nitrogen and air to make it comparable to natural gas before being fed into gas supply lines. LNG is also used as a motor-vehicle fuel as an alternative to gasoline.

Petroleum-associated gases and condensate gases are classified as “rich” gases, because they contain significant amounts of ethane, propane, butane and other saturated hydrocarbons. Petroleum-associated and condensate gases are separated and liquefied to produce liquefied petroleum gas (LPG) by compression, adsorption, absorption and cooling at oil and gas process plants. These gas plants also produce natural gasoline and other hydrocarbon fractions.

Unlike natural gas, petroleum-associated gas and condensate gas, oil processing gases (produced as by-products of refinery processing) contain considerable amounts of hydrogen and unsaturated hydrocarbons (ethylene, propylene and so on). The composition of oil processing gases depends upon each specific process and the crude oils used. For example, gases obtained as a result of thermal cracking usually contain significant amounts of olefins, while those obtained from catalytic cracking contain more isobutanes. Pyrolysis gases contain ethylene and hydrogen.

Combustible natural gas, with a calorific value of 35.7 to 41.9 MJ/m3 (8,500 to 10,000 kcal/m3), is primarily used as a fuel to produce heat in domestic, agricultural, commercial and industrial applications. The natural gas hydrocarbon also is used as feedstock for petrochemical and chemical processes. Synthesis gas (CO + H2) is processed from methane by oxygenation or water vapour conversion, and used to produce ammonia, alcohol and other organic chemicals. Compressed natural gas (CNG) and liquefied natural gas (LNG) are both used as fuel for internal combustion engines. Oil processing liquefied petroleum gases (LPG) have higher calorific values of 93.7 MJ/m3 (propane) (22,400 kcal/m3) and 122.9 MJ/m3 (butane) (29,900 kcal/m3) and are used as fuel in homes, businesses and industry as well as in motor vehicles (NFPA 1991). The unsaturated hydrocarbons (ethylene, propylene and so on) derived from oil processing gases may be converted into high-octane gasoline or used as raw materials in the petrochemical and chemical-processing industries.
Read More → Compressed Natural Gas and Liquefied Hydrocarbon Gases

Composition of Crude oil and Natural gas in Drilling


Relatively simple crude-oil assays are used to classify crude oils as paraffinic, naphthenic, aromatic or mixed, based on the predominant proportion of similar hydrocarbon molecules. Mixed-base crudes have varying amounts of each type of hydrocarbon. One assay method (US Bureau of Mines) is based on distillation, and another method (UOP "K" factor) is based on gravity and boiling points. More comprehensive crude assays are conducted to determine the value of the crude (i.e., its yield and quality of useful products) and processing parameters. Crude oils are usually grouped according to yield structure, with high-octane gasoline being one of the more desirable products. Refinery crude oil feedstocks usually consist of mixtures of two or more different crude oils.

Crude oils are also defined in terms of API (specific) gravity. For example, heavier crude oils have low API gravitates (and high specific gravities). A low-API gravity crude oil may have either a high or low flash point, depending on its lightest ends (more volatile constituents). Because of the importance of temperature and pressure in the refining process, crude oils are further classified as to viscosity, pour points and boiling ranges. Other physical and chemical characteristics, such as color and carbon residue content, are also considered. Crude oils with high carbon, low hydrogen and low API gravity are usually rich in aromatics; while those with low carbon, high hydrogen and high API gravity are usually rich in paraffin.

Crude oils which contain appreciable quantities of hydrogen sulfide or other reactive sulphur compounds are called “sour.” Those with less sulphur are called “sweet.” Some exceptions to this rule are West Texas crude (which are always considered “sour” regardless of their H2S content) and Arabian high-sulfur crudes (which are not considered “sour” because their sulfur compounds are not highly reactive).

Hidrocarbon:

Paraffins: The paraffinic saturated chain type hydrocarbon (aliphatic) molecules in crude oil have the formula CnH2n+2, and can be either straight chains (normal) or branched chains (isomers) of carbon atoms. The lighter, straight chain paraffin molecules are found in gases and paraffin waxes. The branched chain paraffins are usually found in heavier fractions of crude oil and have higher octane numbers than normal paraffins.

Aromatics: Aromatics are unsaturated ring type hydrocarbon (cyclic) compounds. Naphthalenes are fused double ring aromatic compounds. The most complex aromatics, polynuclears (three or more fused aromatic rings), are found in heavier fractions of crude oil.

Naphthenes: Naphthenes are saturated ring type hydrocarbon groupings, with the formula CnH2n, arranged in the form of closed rings (cyclic), found in all fractions of crude oil except the very lightest. Single ring naphthenes (mono-cycloparaffins) with 5 and 6 carbon atoms predominate, with two ring naphthenes (dicycloparaffins) found in the heavier ends of naphtha.

Non-hydrocarbons

Sulphur or sulfur and sulphur compounds: Sulphur is present in natural gas and crude oil as hydrogen sulphide (H2S), as compounds (thiols, mercaptans, sulphides, polysulphides, etc.) or as elemental sulphur. Each gas and crude oil has different amounts and types of sulphur compounds, but as a rule the proportion, stability and complexity of the compounds are greater in heavier crude oil fractions.

Sulphur compounds called mercaptans, which exhibit distinct odours detectable at very low concentrations, are found in gas, petroleum crude oils and distillates. The most common are methyl and ethyl mercaptans. Mercaptans are often added to commercial gas (LNG and LPG) to provide an odour for leak detection.

The potential for exposure to toxic levels of H2S exists when working in drilling, production, transportation and processing crude oil and natural gas. The combustion of petroleum hydrocarbons containing sulphur produces undesirables such as sulphuric acid and sulphur dioxide.

Oxygen compounds: Oxygen compounds, such as phenols, ketones and carboxylic acids, are found in crude oils in varying amounts.

Nitrogen compounds: Nitrogen is found in lighter fractions of crude oil as basic compounds, and more often in heavier fractions of crude oil as non-basic compounds which may also include trace metals.

Trace metals: Trace amounts, or small quantities of metals, including copper, nickel, iron, arsenic and vanadium, are often found in crude oils in small quantities.

Inorganic salts: Crude oils often contain inorganic salts, such as sodium chloride, magnesium chloride and calcium chloride, suspended in the crude or dissolved in entrained water (brine).

Carbon dioxide: Carbon dioxide may result from the decomposition of bicarbonates present in, or added to crude, or from steam used in the distillation process.

Naphthenic acids: Some crude oils contain naphthenic (organic) acids, which may become corrosive at temperatures above 232 °C when the acid value of the crude is above a certain level.

Normally occurring radioactive materials: Normally occurring radioactive materials (NORMs) are often present in crude oil, in the drilling deposits and in the drilling mud, and can present a hazard from low levels of radioactivity.
Read More → Composition of Crude oil and Natural gas in Drilling

Sunday, March 10, 2019

Drillling Geothermal Well with Laser

laser

From fossil fuels to geothermal heat, accessing the planet’s energy riches usually involves boring deep into the Earth with giant metal drills. But could lasers do the same job?

Foro Energy, a start-up company in Littleton, Colorado, has developed what it claims is an inexpensive system of high-powered lasers that can rip through rock, potentially revolutionising drilling and hastening the adoption of greener forms of power.

Foro announced last month that a test system had sent a beam from a 20-kilowatt commercial laser through 1.5 kilometres of optical fibre. Development has been funded by the US Department of Energy’s research arm, ARPA-E. Borehole drilling trials are planned for next year.

Mechanical drills can easily grind through soft rocks like sandstone to tap petroleum reserves, but they wear out quickly in hard crystalline rocks such as granite and basalt. It is these harder rocks that often hide the best sources of geothermal energy. Foro’s intense laser beam heats hard rock surfaces so fast that thermal shock fractures the upper few millimetres, leaving a crumbled layer that a mechanical drill can scrape away quickly and with little wear. This approach could increase drilling rates, a major component in well cost, by up to a factor of 10, says ARPA-E.

But a flashy prototype is far from proof that the rig will hold up in the brutal environment found in the bottom of a borehole, which is filled with rock chips and churning water that lubricates the drill bit. The optics must deliver the beam directly to the rock, says Jared Potter of Potter Drilling in Redwood City, California, who is developing a drilling process that shatters rock with extremely hot water. If the beam hits fluid, it will heat the liquid instead of the rock face. “It’s amazing how much energy it takes to boil water,” Potter says, and even a powerful laser couldn’t hope to zap both water and rock at once. He thinks Foro “has a long way to go to have a tool they can deploy in a geothermal or oil well”.

Still, the cost of drilling has been a roadblock to expanding the adoption of geothermal energy. If Foro can prove its technology is ready for the grunt work of punching hundreds of holes through the hard igneous rocks, it would change the mathematics of low-carbon energy. In the meantime, Potter says Foro’s lasers could be used instead of explosives to make holes in the steel casings of oil and gas wells, which are needed to drain fluid from the surrounding rock.

Read More → Drillling Geothermal Well with Laser

CEMENTING ADDITIVES CHEMICAL

chemical for well drilling
Cementing Additive Chemical

Additional chemicals are used to control slurry density, rheology, and fluid loss, or to provide
more specialized slurry properties. Additives modify the behavior of the cement slurry allowing cement placement under a wide range of downhole conditions. There are many additives available for cement and these can be classified under one of the following categories:

Accelerators: Most operators wait for cement to reach a minimum compressive strength of 500 psi before resuming operations. At temperatures below l00 °F common cement may require a day or two to develop this strength level. chemicals which reduce the thickening time of a slurry and increase the rate of early strength development. Low concentrations of cement accelerators (2-4% by weight of cement) are used to shorten the setting time of cement and promote rapid strength development.They are usually use in conductor and surface casing to reduce waiting on cement time (WOC). Calcium chloride (CaCl2), sodium chloride (NaCl) and sea water are commonly used as accelerators.

Retarders: chemicals which retard the setting time (extend the thickening) of a slurry to aid cement placement before it hardens. Retarders Increased well depths and formation temperatures require the use of cement retarders to extend the pumpability of cements. Most retarders also affect cement viscosity to some extent..These additives are usually added to counter the effects of high temperature.They are used in cement slurries for intermediate and production casings, squeeze and cement plugs and high temperature wells. Typical retarders include: sugar; lignosulphonates, hydroxycarboxylic acids, inorganic compounds and cellulose derivatives.

Retarders work mainly by adsorption on the cement surface to inhibit contact with water and
elongate the hydration process; although there are other chemical mechanisms involved.

Lignosulfonates are used to about 200°F bottom-hole circulating temperature (BHCT). Concentrations of 0.1% to 1% are used in most slurry applications to give both predictable thickening times and compressive strength.

Organic acids can be used from about 200°-400°F BHCT. They are used on concentrations of 0.1% to 2.5% by weight of cement as effective retarders for high temperature environments.

Extenders: materials which lower the slurry density and increase the yield to allow weak
formations to be cemented without being fractured by the cement cloumn.Examples of
extenders include: water, bentonite, sodium silicates, pozzlans, gilsonite, expanded perlite,
nitrogen and ceramic microspheres. Bentonite clay can be used in concentrations up to 25%
by weight of Portland cement to decrease the density.

Weighting Agents (density adjusters): materials which increase slurry density including barite and haematite High-density slurries are used to cement high-pressure wells where increased hydrostatic head is required to hold down gas or fluids. 

- Hematite, sp. gr. of 5, is used to increase slurry density to 21 1b/gal. Barite, sp. gr. 4.2 can
increase slurry weight to 18Ib/gal.

- Sand, sp.gr. 2.65, has a low water requirement and helps to densify slurries to 17.5Ib/gal.

Dispersants: chemicals which lower the slurry viscosity and may also increase free water by dispersing the solids in the cement slurry. Dispersants are solutions of negatively charged polymer molecules that attach themselves to the positively charges sites of the hydrating cement grains.The result is an increased negative on the hydrating cement grains resulting in greater repulsive forces and particle dispersion.

The most common dispersants are aryl-alkyl sulphonates used in concentrations of 0.3% to 2% by weight of cement polyphosphate, lignosulfonate, salt and organic acid.

Fluid-Loss Additives: Excessive fluid losses from the cement slurry to the formation can affect the correct setting of cement. Fluid loss additives are used to prevent slurry dehydration and reduce fluid loss to the formation.Examples include: cationic polymer, nonionic synthetic polymer, anionic synthetic polymer and cellulose derivative.

Lost Circulation Control Agents: materials which control the loss of cement slurry to weak or fractured formations.

Strength Retrogression: At temperatures above 230 F, normal cement develop high permeability and reduction in strength. the addition of 30-40% BWOC (by weight of cement) silica flour prevents both strength reduction and development of permeability at high temperatures.

Miscellaneous Agents: e.g. Anti-foam agents, fibres, latex.
Read More → CEMENTING ADDITIVES CHEMICAL

TYPES OF CASING PIPE

oil gas casing pipe for drilling
Casing Pipe for Oil Gas Well

In practice, it would be much cheaper to drill a hole to total depth (TD), probably with a small
diameter drill bit, and then case the hole from surface to TD. However, the presence of high pressured zones at different depths along the wellbore, and the presence of weak, unconsolidated formations or sloughing, shaly zones, necessitates running casing to seal off these troublesome zones and to allow the drilling to TD. Thus, different sizes of casing are employed and this arrangement gives a tapered shape to the finished well. 

The types of casing currently in use are as follows:
  1. Stove Pipe

Stove pipe (or marine-conductor, or foundation-pile for offshore drilling) is run to prevent washouts of near-surface unconsolidated formations, to provide a circulation system for the drilling mud and to ensure the stability of the ground surface upon which the rig is sited. This pipe does not usually carry any weight from the wellhead equipment and can be driven into the ground or seabed with a pile driver. A typical size for a stove pipe ranges from 26 in. to 42 in.

    2. Conductor Pipe

Conductor pipe is run from the surface to a shallow depth to protect near surface unconsolidated formations, seal off shallow-water zones, provide protection against shallow gas flows, and provide a conduit for the drilling mud. One or more BOPs may be mounted on this casing or a diverter system if the setting depth of the conductor pipe is shallow. In the Middle East, a typical size for a conductor pipe is either 18 5/8 in. (473 mm) or 20 in. (508 mm). In North Sea exploration wells, the size of the conductor pipe is usually 26 or 30 in also in most of Iraqi wells. Conductor pipe is always cemented to surface. It is used to support subsequent casing strings and wellhead equipment or alternatively the pipe is cut off at the surface after setting the surface casing.

 3. Surface Casing

Surface casing is run to prevent caving of weak formations that are encountered at shallow
depths. This casing should be set in competent rocks such as hard limestone. This will ensure that formations at the casing shoe will not fracture at the high hydrostatic pressures which may be encountered later. The surface casing also serves to provide protection against shallow blowouts, hence BOPs are connected to the top of this string. The setting depth of this casing string is chosen so that troublesome formations, thief zones, water sands, shallow hydrocarbon zones and build-up sections of deviated wells may be protected. A typical size of this casing is l3 3/8 in. (240 mm) in the Middle East and 18 5/8 in. or 20 in. in North Sea operations.

4. Production Casing

Production casing is the last casing string. It is run to isolate producing zones, to provide reservoir fluid control and to permit selective production in multizone production. This is the string through which the well will be completed. The usual sizes of this string are 4 1/2, 5 and 7 in.

6. Liners

A liner is a string of casing that does not reach the surface. Liners are hung on the intermediate casing by use of a liner-hanger. In liner completions both the liner and the intermediate casing act as the production string. Because a liner is set at the bottom and hung from the intermediate casing, the major design criterion for a liner is usually the ability to withstand the maximum expected collapse pressure.
Read More → TYPES OF CASING PIPE

PDC BITS APPLICATIONS

type of bit for drilling oil gas well
PDC Bit

PDC bits have been used extensively and successfully over a wide range of formation types. The lack of rotating parts leads to greater life expectancy and as such long bit runs are achievable with resultant time and cost savings. A thorough review of the economics of running a PDC bit needs to be performed prior to selection due to its increased cost. 

The following guidelines list the typical applications of PDC bits.
  1. PDC bits are typically useful for drilling long, soft to medium shale sequences which have a low abrasivity. In such formations they typically exhibit high ROP and extended life enabling entire sections to be drilled on one run.
  2. PDC bits are not usually appropriate for highly abrasive well cemented sand sequences.When drilling tight siliceous formations the incidence of PDC chipping and breaking is dramatically increased resulting in less than expected ROP and bit life.
  3. When drilling heterogeneous formations containing alternating shales and or shale limestone sequences the use of hybrid PDC bits is encouraged. This bit incorporates the use of back-up diamond studs behind the PDC cutter. When drilling harder abrasive strings, the diamond stud absorbs the increased weight required to drill the stringer and prevents premature damage and wear to the PDC cutter.
  4. The use of bladed hybrid PDC bits is recommended for drilling hard formations. The deep watercourse on these bits enable optimum fluid flow across the cutter to efficiently reduce the friction temperatures induced. This efficient cooling will help minimise fracture of the PDC cutters.
  5. When drilling mobile, plastic formations such as salt sections the use of eccentric PDC bits should be considered. These bits have proved successful in preventing incidence of stuck pipe in many areas where salt flow problems are experienced.
Read More → PDC BITS APPLICATIONS